PRODUCTS CENTER

Preformed Permanent Anti-stain pavement marking tapes (Smooth Surface)
Preformed Permanent Anti-stain pavement marking tapes (Smooth Surface)

Preformed Permanent Anti-stain pavement marking tapes (Smooth Surface)

Preformed Permanent Anti-stain pavement marking tapes does not contain glass beads on the surface. It is made by combining high-performance coatings, flexible polymer, wear-resistant layer, substrate, high-strength adhesive, release film, and other materials.

关键词:

Engineered stain resistant marking tape

电话

Product details

Product Information

Brand: Cai Lu

Item No.:L5020X(without adhesive backing),L5021X(with adhesive backing)

Color: white, yellow, red, blue, black, green

Product Features

--The surface is free of glass beads, smooth surface, and easy to clean. The base material of the preformed material is composed of polymer flexible polymer rubber, fillers, pigments, etc., and a layer of high wear-resistant and environmentally friendly paint is planted on the surface. It has the characteristics of strong wear resistance,  good weather resistance, long durability, and convenient and quick construction.

--The main advantage is that it is resistant to dirt and eye-catching, even if it is dirty, it is easy to clean. It can be made into various marking lines, arrows, characters, patterns, color signs, logos, color three-dimensional signs, pipeline signs, etc.

--It is suitable for rubber products, concrete, asphalt, cement, marble, epoxy floor, ceramic tile, etc. It is basically suitable for bonding various floors and walls. This product is recommended for indoor use on various floors and surfaces that require anti-pollution and dirt resistance. Works best on walls.


--According to the condition of the road surface, the flow of people, and the installation situation, the service life can reach at least 3 years.

Product size reference chart

Product number Length(M) Width(CM) Thickness(MM) Weight(±10%) Conventional packaging Adhesive
L5020X 50M 5,10,15,20,Customizable 1.0-1.5MM 2.0kg/sqm 260*260*400MM without adhesive backing
L5021X 50M 5,10,15,20,Customizable 1.2-2.0MM 2.2kg/sqm 260*260*400MM with adhesive backing

 

Technical Parameters

Nature

General data

Unit

Test Methods

L50211

L50212

________

________

Color

white

yellow

________

________

Thickness

1.3

1.3

mm

GB/T 7125

Water resistance

pass

pass

________

GB/ T24717

Acid resistance

pass

pass

________

GB/T 24717

Wear-resistant

40

40

mg

GB/T24717

Minimum adhesion

25

25

N/25mm

GB/T24717

Instructions:

1. The pavement marking tape without adhesive backing is commonly used in special environments and special materials, using special glue, such as two-component AB glue, 502 glue, etc.


2. The products with adhesive backing can be divided into ground brush primer and ground primer without brush according to the usage:

  • Without brush primer on the ground: It can be directly applied to smooth and flat surfaces without applying primer when used indoors, on outer pavement, and on various walls of place such as workshops, exhibition halls, squares, safety islands of toll stations, where few vehicles run over, it only needs rip off the isolated paper on the back of the product and sticks it directly to the joint surface. And its life can be 5 years to the longest.
  • Brush primer on the ground: It should be applied with primer on uneven surfaces or walls(e.g., Pattex Contact Adhesive, Maxbond UL 1603HFR-HS). The amount of primer required depends on the smoothness of the bonding surface, approximately 1 kilogram per 3 to 5 square meters. Please refer to the construction instructions when using the primer.

Online
Message


If you have any suggestions or feedback about our company, please fill in the relevant information on this page and submit it. Our staff will contact you in a timely manner, or please call us directly.

电话

Submit